Canoe slalom is a competitive sport where the aim is to navigate a decked canoe or kayak through a course of hanging gates on river rapids in the fastest time possible. It is one of the two kayak and canoeing disciplines at the Summer Olympics, and is referred to by the International Olympic Committee (IOC) as Canoe slalom. The other Olympic canoeing discipline is canoe sprint. There is also wildwater, a non-Olympic paddlesport. Whitewater slalom racing started in Europe and in the 1940s, the International Canoe Federation (ICF) was formed to govern the sport. The first World Championships were held in 1949 in Switzerland. From 1949 to 1999, the championships were held every odd-numbered year and have been held annually in non-Summer Olympic years since 2002. Folding kayaks were used from 1949 to 1963; and in the early 1960s, boats were made of fiberglass, and nylon. Boats were heavy, usually over 65 pounds (30 kilos). With the advent of kevlar and carbon fibre being used in the 1970s, the widths of the boats were reduced by the ICF, and the boats were reduced in volume to pass the gates, and boats have become much lighter and faster. From 1949 to 1977, all World Championships were held in Europe. The first World Championship held in North America was held at Jonquiere, in Quebec, Canada in 1979.
Rules
Each gate consists of two poles hanging from a wire strung across the river. There are 18-25 (although nowadays there are more often near 18 than 25) numbered gates in a course and they are colored as either green (downstream) or red (upstream), indicating the direction they must be negotiated. Upstream gates are often placed in eddies, where the water is flat or moving slightly upstream; the paddler eddies out from the main current and paddles upstream through the gate. Most slalom courses take 80 to 120 seconds to complete for the fastest paddlers. Depending on the level of competition, difficulty of course, degree of water turbulence and ability of the other paddlers, times can go up to 200 seconds. Each competitor has two runs on the course, and the final result is based either on the faster run (in smaller races or lower division races) or the sum of the two runs (in national and international competitions). In international competitions (World Cups, World Championships,Olympic Games) each competitor does two runs in the qualification round, the times are added to give the qualification result. Depending on the number of participants of the event, 10 to 40 boats make it through to the semi-final; this consists of one run on a different course. The fastest 10 boats per event make it through to the final, where they navigate the semi-final course once more and times of semi-final and final run are added to give the final result.
If the competitor's boat, paddle or body touches either pole of the gate, a time penalty of two seconds is added. If the competitor misses a gate completely, displaces it by more than 45 degrees, goes through the gate upside-down, or goes through it in the wrong order, a 50 second penalty is given.
Development of Slalom Boats In the 1960s and early 1970s, boats were made of heavy fiberglass and nylon. The boats were high volume and weighed over 65 pounds (30 kilos). In the early 1970s Kevlar was used and the boats became lighter as well as the volume of the boats was being reduced almost every year as new designs were made. A minimum boat weight was introduced to equalize competition when super light materials began to effect race results. The I.C.F also reduced the width of the boats in the early 1970s. The gates were hung about 10 cm above the water. When racers began making lower volume boats to sneak underneath gates, the gates were raised in response to fears that new boats would be of such low volume as to create a hazard to the paddler. Their low volume sterns allow the boat to slice through the water in a quick turn, or 'pivot'.
Typically, new racing boats cost between £650 onwards for the cheapest constructions in fibreglass. Usually boats are made with carbon fibre, Kevlar, and fiberglass cloth, using epoxy or polyester resin to hold the layers together. Foam sandwich construction in between layers of carbon, Kevlar, or Aramid is another technique in use to increase the stiffness of slalom boats.
Recently, the minimum length of these boats were reduced from 4 meters down to 3.5 meters, causing a flurry of new, faster boat designs which are able to navigate courses with more speed and precision. The shorter length also allows for easier navigation and less boat damage in the smaller man made river beds that are prevalent in current elite competitions.
Boat design progression is rather limited year to year. Designs tend to focus on providing optimal performance for upcoming critical race venues. Olympic years tend to generate boat designs with specific performance characteristics tuned for the upcoming Olympic course.
Slalom boats used in competition must meet the ICF specifications for the class. Directly from the 2005 ICF Slalom rules:
7.1.1 Measurements
All types of K1 Minimum length 3.50 m minimum width 0.60 m
All types of C1 Minimum length 3.50 m minimum width 0.65 m
All types of C2 Minimum length 4.10 m minimum width 0.75 m
7.1.2 Minimum Weight of Boats
(The minimum weight of the boat is determined when the boat is dry)
All types of K1 9 kg.
All types of C1 10 kg.
All types of C2 15 kg.
7.1.3 All boats must have a minimum radius at each end of 2 cm horizontally and 1 cm vertically.
7.1.4 Rudders are prohibited on all boats
7.1.5 Boats must be designed to, and remain within, the required dimensions.
7.1.6 Kayaks are decked boats, which must be propelled by double bladed paddles and inside which the competitors sit. Canadian canoes are decked boats that must be propelled by single-bladed paddles and inside which the competitors kneel.
There are rules governing almost every aspect of slalom equipment used in major competition, including sponsor advertisement. Some of these rules vary from country to country, consult your national canoe and kayak governing body for direct rules.
It is common for boat manufacturers to build elite competition quality boats lighter than the required ICF weight, thus competitors affix weight to the inside of the boat at the center point. This practice allows the boat to be more responsive to directional adjustments.
Rules
Each gate consists of two poles hanging from a wire strung across the river. There are 18-25 (although nowadays there are more often near 18 than 25) numbered gates in a course and they are colored as either green (downstream) or red (upstream), indicating the direction they must be negotiated. Upstream gates are often placed in eddies, where the water is flat or moving slightly upstream; the paddler eddies out from the main current and paddles upstream through the gate. Most slalom courses take 80 to 120 seconds to complete for the fastest paddlers. Depending on the level of competition, difficulty of course, degree of water turbulence and ability of the other paddlers, times can go up to 200 seconds. Each competitor has two runs on the course, and the final result is based either on the faster run (in smaller races or lower division races) or the sum of the two runs (in national and international competitions). In international competitions (World Cups, World Championships,Olympic Games) each competitor does two runs in the qualification round, the times are added to give the qualification result. Depending on the number of participants of the event, 10 to 40 boats make it through to the semi-final; this consists of one run on a different course. The fastest 10 boats per event make it through to the final, where they navigate the semi-final course once more and times of semi-final and final run are added to give the final result.
If the competitor's boat, paddle or body touches either pole of the gate, a time penalty of two seconds is added. If the competitor misses a gate completely, displaces it by more than 45 degrees, goes through the gate upside-down, or goes through it in the wrong order, a 50 second penalty is given.
Development of Slalom Boats In the 1960s and early 1970s, boats were made of heavy fiberglass and nylon. The boats were high volume and weighed over 65 pounds (30 kilos). In the early 1970s Kevlar was used and the boats became lighter as well as the volume of the boats was being reduced almost every year as new designs were made. A minimum boat weight was introduced to equalize competition when super light materials began to effect race results. The I.C.F also reduced the width of the boats in the early 1970s. The gates were hung about 10 cm above the water. When racers began making lower volume boats to sneak underneath gates, the gates were raised in response to fears that new boats would be of such low volume as to create a hazard to the paddler. Their low volume sterns allow the boat to slice through the water in a quick turn, or 'pivot'.
Typically, new racing boats cost between £650 onwards for the cheapest constructions in fibreglass. Usually boats are made with carbon fibre, Kevlar, and fiberglass cloth, using epoxy or polyester resin to hold the layers together. Foam sandwich construction in between layers of carbon, Kevlar, or Aramid is another technique in use to increase the stiffness of slalom boats.
Recently, the minimum length of these boats were reduced from 4 meters down to 3.5 meters, causing a flurry of new, faster boat designs which are able to navigate courses with more speed and precision. The shorter length also allows for easier navigation and less boat damage in the smaller man made river beds that are prevalent in current elite competitions.
Boat design progression is rather limited year to year. Designs tend to focus on providing optimal performance for upcoming critical race venues. Olympic years tend to generate boat designs with specific performance characteristics tuned for the upcoming Olympic course.
Slalom boats used in competition must meet the ICF specifications for the class. Directly from the 2005 ICF Slalom rules:
7.1.1 Measurements
All types of K1 Minimum length 3.50 m minimum width 0.60 m
All types of C1 Minimum length 3.50 m minimum width 0.65 m
All types of C2 Minimum length 4.10 m minimum width 0.75 m
7.1.2 Minimum Weight of Boats
(The minimum weight of the boat is determined when the boat is dry)
All types of K1 9 kg.
All types of C1 10 kg.
All types of C2 15 kg.
7.1.3 All boats must have a minimum radius at each end of 2 cm horizontally and 1 cm vertically.
7.1.4 Rudders are prohibited on all boats
7.1.5 Boats must be designed to, and remain within, the required dimensions.
7.1.6 Kayaks are decked boats, which must be propelled by double bladed paddles and inside which the competitors sit. Canadian canoes are decked boats that must be propelled by single-bladed paddles and inside which the competitors kneel.
There are rules governing almost every aspect of slalom equipment used in major competition, including sponsor advertisement. Some of these rules vary from country to country, consult your national canoe and kayak governing body for direct rules.
It is common for boat manufacturers to build elite competition quality boats lighter than the required ICF weight, thus competitors affix weight to the inside of the boat at the center point. This practice allows the boat to be more responsive to directional adjustments.